Request a Quote
Application · Molding & bonding

Molded Rubber Products

Stall mats, gym tiles, pavers, wheel chocks, curb stops and speed bumps all start as crumb and binder. Here's which grades molders run, how binder math works, and how much crumb a line eats.

Molded recycled rubber wheel chocks, speed bump, pavers and curb stop

The biggest crumb rubber market in the U.S.

According to the U.S. Tire Manufacturers Association's 2021 scrap tire report, molded and extruded products such as rubber mats and flooring consumed 485 thousand tons of scrap tires in 2021, up 25 percent from 2019. That made it the largest single segment of the ground rubber market.

If you mold, you already know the problem: steady crumb, in the right size, every month.

How bonded rubber products are made

Most mats, tiles and pavers are bonded: crumb is coated with a binder (commonly a polyurethane prepolymer based on MDI), packed into a mold, and cured under heat and/or pressure. Thick goods can be compression molded; rolled flooring is often cut from a large molded cylinder ("bun").

Binder levels are published by binder makers. Huntsman's sell sheet for its SUPRASEC® MDI in molded rubber crumb applications states:

  • Molded cylinders: 5-6% binder by weight
  • Smaller molded products: 3-10% binder by weight

Finer crumb has more surface area to coat, so it generally needs more binder for the same mass. That's why many products use a coarse core and a fine face.

Stack of recycled rubber stall mats on a pallet in a barn aisle
Recycled rubber stall mats: a classic 10-20 mesh or coarser molded product.

Which grade for which product

Product Grades molders commonly run Why
Stall mats, trailer mats 10-20, 8-16, ABR Thick, tough, resilient
Gym tiles and rolled flooring 10-20 core, 20-30 or 30-minus face Clean surface, consistent density
Pavers and walkway tiles 10-20, 8-16 Drainage, bulk
Wheel chocks, curb stops, speed bumps ABR, 8-16, 10-20 Mass and resilience
Fine-faced mats, anti-fatigue mats 30-minus, 40 mesh Smooth finish

These are starting points. Your mold, your binder, your test results decide.

Worked examples

Example 1: 4×6 stall mats

A shop makes 4 ft × 6 ft stall mats from 10-20 mesh at 8% binder. Plan by mix weight:

  • For every 20,000 lb of finished mix, binder = 1,600 lb and crumb = 18,400 lb of 10-20
  • That's roughly 9 supersacks, about half a truckload
  • Our ~200,000 lb/month of 10-20 supports about 217,000 lb/month of finished mats at that ratio

Example 2: Rolled flooring from a 5.5% bun

A flooring maker molds cylinders at 5.5% binder (Huntsman's 5-6% range) using 10-20 mesh with a colored EPDM fleck. Per 40,000 lb of buns:

  • Binder: 40,000 × 5.5% = 2,200 lb
  • If 10% of the mix is color fleck, crumb = 40,000 − 2,200 − 4,000 = 33,800 lb, about 17 supersacks

Steady cylinder production means steady crumb. Set up a recurring program.

Example 3: Two-grade wheel chocks

A chock maker uses ABR for the body and 30-minus as a 15% face layer, at 6% overall binder, making 20,000 lb of chocks a month:

  • Crumb total = 20,000 × 94% = 18,800 lb
  • 30-minus face = 15% of crumb ≈ 2,820 lb; ABR = 15,980 lb
  • Both grades ride on one truck, separately sacked

Running a molding line? Price a monthly program. Send grade, volume, delivery city/ZIP and your target price.

Request a Quote

What molders should spec

  1. Sieve curve (ASTM D5644), not just a mesh label. Fines change binder demand.
  2. Residual steel and fiber. Fiber balls show up on the mat face; steel damages molds and knives.
  3. Moisture. Moisture reacts with isocyanate binders. Set a limit.
  4. Source. ASTM D5603 classifies recycled rubber by parent material. If color or polymer type matters, say so.
  5. Packaging. Supersacks with or without pallets, to fit your feed system.

See crumb rubber specs explained for how to read a lot sheet.

Frequently asked questions

What mesh crumb rubber is best for rubber mats?

10-20 mesh is the most common mat granule; coarser 8-16 and ABR are used for thick mats, and finer 20-30 or 30-minus for smooth faces.

How much binder do molded rubber products use?

Huntsman's published range is 3-10% by weight for smaller molded products and 5-6% for molded cylinders. Your binder supplier and product testing set the final number.

Does moisture in crumb matter for polyurethane binders?

Yes. Isocyanate binders react with water, so moisture affects cure. Our spec sheets list typical moisture; set your own limit and we'll check the lot.

Can you supply color-matched or EPDM?

We supply black recycled tire crumb. Molders typically buy color granules separately.

Sources: USTMA 2021 US Scrap Tire Management Summary (summary); Huntsman SUPRASEC® MDI for Rubber Crumb Molded Applications sell sheet; ASTM D5603-23, D5644-23.

Need crumb rubber
by the truckload?

Send your grade, quantity and delivery ZIP or export destination. We'll review availability, packaging and freight, then come back with a written quote.

Request a Quote CallEmail