Request a Quote
Guide · Sizing

Crumb Rubber Mesh Size Guide

Mesh numbers trip up more crumb rubber orders than anything else. Here's the chart, the ASTM rules behind the labels, and how to read a sieve report like a buyer who's been burned before.

Four piles of tire rubber from coarse chip to 10-20 mesh, 30 mesh and 80 mesh powder

What "mesh" means

A mesh number refers to a standard test sieve. In the U.S., sieve openings are set by ASTM E11. Higher number, smaller opening. A No. 10 sieve has a 2.00 mm opening; a No. 40 has 425 µm; a No. 80 has 180 µm.

When someone says "10 mesh rubber," they mean rubber that passes a No. 10 sieve. When they say "10-20," they mean it passes No. 10 and is mostly caught on No. 20. When they say "30-minus," they mean it passes No. 30, with everything finer included.

Mesh-to-millimeter chart

U.S. standard sieve sizes (ASTM E11 openings)
Sieve No. (mesh)OpeningApprox. inches
No. 63.35 mm0.132 in
No. 82.36 mm0.093 in
No. 102.00 mm0.079 in
No. 141.40 mm0.055 in
No. 161.18 mm0.046 in
No. 20850 µm0.033 in
No. 30600 µm0.024 in
No. 40425 µm0.017 in
No. 50300 µm0.012 in
No. 80180 µm0.007 in
No. 100150 µm0.006 in
No. 20075 µm0.003 in

Quick mental anchors:

  • No. 10 (2 mm): coarse sand
  • No. 20 (0.85 mm): medium sand
  • No. 40 (0.425 mm): fine sand / table salt
  • No. 80 (0.18 mm): flour-like powder

How ASTM defines a mesh product

ASTM D5603, Standard Classification for Rubber Compounding Materials—Recycled Vulcanizate Rubber, defines product size with two sieves:

  • A zero screen, the next sieve up, on which nothing may be retained
  • A designation screen, on which only a small maximum percentage may be retained

ASTM D5644 (the sieve-shaker test method) states the allowed retained maximum is 5% for products up to 850 µm (20 mesh), 10% for 850-150 µm (20 to 100 mesh), and 15% for 125-20 µm (120 to 635 mesh).

ASTM D5603 mesh designations (examples)
Product designationZero screen (0% retained)Designation screenMax retained on designation screen
10 meshNo. 8 (2.36 mm)No. 10 (2.00 mm)5%
20 meshNo. 16 (1.18 mm)No. 20 (850 µm)5%
30 meshNo. 20 (850 µm)No. 30 (600 µm)10%
40 meshNo. 30 (600 µm)No. 40 (425 µm)10%
80 meshNo. 60 (250 µm)No. 80 (180 µm)10%

Summarized from ASTM D5603 Table 1 / ASTM D5644 §4.2. Buy the current standard from ASTM for the full table.

So under ASTM rules, a "30 mesh" product may have up to 10% held on the No. 30 sieve but nothing on the No. 20. That's tighter than a lot of loose trade talk.

Lab technician weighing crumb rubber retained on a test sieve beside a sieve shaker
A sieve analysis: weigh what each screen retains, and the curve tells you what you bought.

Range grades vs. minus grades

Crumb rubber is sold two ways:

Type Example What you get
Range (window) grade 10-20, 8-16, 20-30, 6-10 Material between two screens. Fines mostly removed.
Minus grade 30-minus, 40-minus Everything below a top size, fines included

Range grades are more uniform; minus grades are usually higher volume and lower cost. Neither is "better." The application decides.

How to read a sieve report

A sieve report lists each screen and the percent retained (or passing). Here's a representative 30-minus curve, like the one on our 30-minus page:

Sieve % retained Cumulative % passing
No. 30 (600 µm) 12 88
No. 35 (500 µm) 23 65
No. 40 (425 µm) 18 47
No. 50 (300 µm) 22 25
No. 80 (180 µm) 17 8
No. 100 (150 µm) 4 4
Pan 4 0

What to look at:

  1. Top screen. Anything on the zero screen is oversize. Ask why.
  2. Where the bulk sits. Here, 63% is between 600 and 300 µm.
  3. Fines. Material through No. 80 and No. 100 drives binder demand, dust and caking.
  4. Test method. ASTM D5644 covers particles down to 90 µm. For powders finer than that, other methods are used.

Worked example: comparing two quotes

"Same" product, different curves

Two suppliers quote "30-minus." Supplier A's lot shows 4% through No. 100; Supplier B's shows 15%.

If you're molding with polyurethane binder, B's extra fines soak up more binder, so you may need more binder per pound of crumb to get the same strength. If you're making a terminal-blend asphalt binder, B's fines may react faster. Same label, different behavior.

Always compare sieve reports, not names.

Common grades and where they go

Grade Size range Typical uses Our page
6-10 / 6-14 ABR 3.35-2.0 / 3.35-1.4 mm Thick molded goods, base courses ABR
8-16 2.36-1.18 mm Turf infill, molded goods 8-16
10-20 2.00-0.85 mm Turf, mats, surfacing 10-20
20-30 850-600 µm Fine-faced molded goods, binders 20-30
30-minus <600 µm Asphalt, molded faces, export 30-minus
40 mesh ~425 µm and finer Binders, sealants 40 mesh
80 mesh ~180 µm and finer Coatings, compounding 80 mesh

For size terms beyond crumb: ASTM D6270 calls particles up to 2 mm "ground rubber," up to 12 mm "granulated rubber," and 12-305 mm pieces "tire-derived aggregate."

Know your mesh? Get a quote. Send grade, volume, delivery city/ZIP and your target price.

Request a Quote

Frequently asked questions

What is 30-minus crumb rubber in millimeters?

It passes a 600 µm (0.6 mm) opening. Everything is 0.6 mm or smaller.

Is a higher mesh number finer or coarser?

Finer. Higher mesh numbers mean smaller sieve openings.

What does 10-20 mesh mean?

Passes a No. 10 sieve (2.00 mm) and is mostly retained on a No. 20 sieve (850 µm).

Which ASTM standard covers crumb rubber particle size?

ASTM D5644 is the test method; ASTM D5603 is the classification that uses it.

Are mesh and micron interchangeable?

They're two ways of naming the same opening. Use the chart above to convert.

Sources: ASTM E11 (sieve openings); ASTM D5603-23 (astm.org); ASTM D5644-23 §4.2 (astm.org); ASTM D6270 definitions.

Need crumb rubber
by the truckload?

Send your grade, quantity and delivery ZIP or export destination. We'll review availability, packaging and freight, then come back with a written quote.

Request a Quote CallEmail